[whatsisface] sent in his scratch built clone of a Griffin PowerMate. The PowerMate... is just a big knob, so it's easy to see why more than one person has attempted this. [whatsisface] was inspired by a bit-tech post that did nearly the same thing, only they used the head out of a VCR for the knob. All the other components, like the optical encoder, are salvaged from a mouse, which we talked about in our scavenging How-To. He used a RC car tire for the actual knob. While we're sure it works great in dirt, we'd probably go with the weight and inertia of the VCR head instead. Have a look at the video below to see the knob being used with the Volumouse software.
As promised, [tnkgrl] has published part two of Acer Aspire One upgrade. In part one she added Bluetooth and more RAM. This time around she focuses on the storage. The subnotebook comes from the factory with an 8GB SSD. The flash based storage readily unplugs from a small ZIF connector. [tnkgrl] replaced it with a 60GB PATA Samsung drive salvaged from an iPod. It's a 1.8inch disk and is only 5mm thick, so it can be tucked under the motherboard. Knowing its previous use, it should prove fairly resilient. You can view a video of the swap and more photos on Flickr.
Up next is part three, where she'll add 3G support.
[tnkgrl], a regular around here, is at it again. This time she has modded an Acer Aspire One subnotebook to have internal Bluetooth. She's released part 1 of a multi part tutorial on beefing up the Aspire One. In this part, she covers disassembly, adding more RAM, and adding the Bluetooth hardware. She suggests that you look at her Bluetooth install on an Asus 701 to find more information as the process is nearly identical.
Part 2 of the tutorial is going to cover upgrading the SSD to a 1.8" PATA hard drive and putting it back together.
Apparently you can run pretty much anything on a PS3. [mopx0] has managed to get Vista running on his PS3. He used Qemu 9.0.1 to install Vista on a PC. He says it takes "about a day or so", after using Vlite to speed it up, so be patient. You then make an image of the install and copy it to your PS3. Don't worry though, your hard work will be rewarded by a speedy 25 minute boot time when you're done.
Even though it is extremely slow, to the point of being nearly unusable, its good to see people pushing the boundaries of our hardware's intended use.
[sprite_tm]'s back with one of his excellent Atmel projects. This time he decided to turn an original XBox controller (cause he likes 'em) into a standard USB HID device. He gutted the custom USB chip that Microsoft installed and replaced it with an Atmel ATMega88. The ATMega required a few changes to the board, but nothing too off the wall.
[Lindsay Williams] has come up a novel way of constructing custom physical inputs for your programs. SenseSurface is a viable alternative to building a new interface for each application. Simply place the dials, buttons, and sliders on your screen wherever you want them.
A sensor board, placed behind the display, picks up the signals from the inputs. The only limitation to the number of inputs available is the size of your screen. Inputs are held on magnetically, and have a low friction backing to avoid scratching or gouging your screen.
[Elf] sent in this interesting DIY joystick glove. There aren't many details on the actual glove switch design, but from the schematic on the site, it seems to mostly consist of micro-switches with some pot adjusted transistors to calibrate the X-Y signals.
You might remember [Janne]'s IKEA cluster. Now he's got a couple of dream rigs in mind, so he started doing 3D renderings of them. Helmer 2 is designed to contain 24 video cards attached to six motherboards with quad core CPUs. (AMD has even taken enough interest to send him some cpus to get started) The rendering really comes in handy for designing the custom copper heat pipes and the aluminum cooling fin enclosure. Still bored, he put together a rendering of a 4 PetaFLOP machine using 2160 video cards. Update: The Helmer 2 link is fixed.
[Jipa] over at MetkuMods put up an original re-use for old hard drives: make em into power tools. The tiny servo motor that drives the spindle doesn't generate much torque, but once the drive is spinning fast enough, the inertial force of the platter is enough to make it usable for small grinding/sanding projects. The platters are re-stacked directly on top of each other to increase strength - we'd suggest a few dabs of epoxy to make em even stronger. Once stacked, a piece of sand paper is cut to size and held on by the center platter washer. [Via hacknmod]
InformationWeek has great article on open source data recovery tools. What type of tools you use will depend on the severity of the situation. You can use live Linux distros designed for recovery like SystemRescueCD or Partedmagic (the latter being more user friendly). Security tools distrubutions like BackTrack can also be helpful; Helix in particular was designed for forensics work. dd is a standard *nix tool for imaging drives, but something like TestDisk can help you repair partition tables for whole disk recovery. Most deletion operations don't overwrite the data which means you can use file carving to capture the lost files. PhotoRec is able to find files in a number of common formats. Finally, if you've got some serious forensic work ahead of you there's The Sleuth Kit and many other command line tools.
The people at TweakTown completely disassembled a new Eee PC 1000H and documented the entire process. Aside from showing you the side effects of too much tech fetish and not enough regular fetish, the article reveals all the parts of the new Eee, with a few surprises inside. Although it's an Eee PC, it's very different from all of its predecessors.
One of the things the teardown shows is that several parts are far more modular than previous Eee PC models. The hard drive, for example, is a standard Seagate Momentus which is made for desktop systems; it can easily be swapped out. Another easily swapped component is the 1GB SIMM from ASint.
Although their (ahem) stripping process was a bit unconventional, a lot of interesting information was yielded from this teardown. Keep 'em coming, TweakTown, just be sure to clean off your tool when you're done.
The folks from bit-tech have done us a great service by tearing open the Eee PC 901. Under the keyboard is a large metal plate that acts as the processor's heat sink. The 4GB SSD card is not soldered to the board this time around. There is some empty space labeled IDE3 and solder points that say 3GCard, which definitely deserve further investigation. The oddest thing they found was a button with no indication to its purpose. It looks like a good machine and we hope to see more Eee PC hacks in the future.
With the imminent release of Firefox 3 and Opera 9.5 being finalized this week, Lifehacker decided it was a good time to run the browsers head to head to see which was the fastest and least resource intensive. The testing system was a 2GHz 2GB Vista machine. The timing system used wasn't directly hooked to the browser, so tests were repeated multiple times to improve accuracy. The cold start winner was Opera, but most browsers opened in about a second if they had been run recently. Safari did well loading content in multiple tabs at the same time, probably due to its short render times for JavaScript and CSS. The final test was memory usage; we're sure many people will be happy to know that Firefox 3 RC3 only used 66% of the RAM required by the other three browsers.
On June 23rd, EFiX is planning on releasing a USB dongle that will let any PC boot and install OSX from a retail DVD. The commercial device is supposed to take care of all patching and other woes OSX86 enthusiasts have had to deal with. Very little information is provided other than a statement that the development process took a lot of time and that they overcame "sabotage"... so, it's got that going for it. Major OSX86 contributor (and Psystar hater) [Netkas] received a device to test and was pleased with the results. We're just going to wait and see what happens. Not that it matters; they have no plans of releasing it in the US.
Some people are really picky about their trackpads. [John] posted a guide on retrofitting a Synaptics pad in place of the newer, but less user friendly ALPS touchpad/stick combo used in the Dell Inspiron 8200. On the opposite end, [C. Järnåker], loves laptop keyboards enough to mod them for use on his desktop machine.
